回采巷道过断层施工技术

受断层影响,巷道过断层期间掘进速度缓慢,影响采掘接替和矿井生产效率。为了更好地促进矿井生产,以23上04轨顺掘进为研究对象,采用FLAC 3D软件模拟巷道过断层时巷道围岩变形量和塑性区范围,并将围岩划分为正常围岩、过渡带和破碎带3部分。根据模拟结果可知,围岩变形量和塑性区范围都在过渡带开始增大,在破碎带达到最大值。巷道采用后退卧底法过断层,并对断层破碎带及时采用锚网索、注浆、U型钢棚进行支护,通过联合支护相互配合,可以共同提高巷道支护强度,增强巷道顶帮抗变形能力。     

前和煤业东胶带运输大巷钻孔卸压围岩控制技术

为有效解决前和煤业3#煤层东胶带大巷在原有锚网索支护下围岩变形量大的问题,结合巷道变形特征,确定采用钻孔卸压技术,采用理论分析和数值模拟的方式确定卸压钻孔在修巷作业前,垂直于巷帮打设,钻孔深度为8 m,结合巷道的具体条件确定巷道采用卸压钻孔+让压支护的围岩控制方案,并采用矿压监测验证支护效果。结果表明:支护方案实施后,顶底板和两帮的最大移近量分别为141 mm和132 mm,有效解决了巷道两帮及底板鼓起量大的问题,保证了巷道围岩的稳定性。     

β-环糊精修饰Ni/SFCC强化C9石油树脂催化加氢性能

以废弃的流化催化裂化催化剂（简称SFCC）为载体、β-环糊精为金属络合剂、硝酸镍为镍源，采用湿法浸渍法制备β-环糊精修饰的Ni/SFCC催化剂（简称Ni/SFCC-CD催化剂），考察其对C9石油树脂的催化加氢性能。通过BET比表面积测试、H2程序升温还原、X射线光电子能谱等手段对催化剂的物相结构进行表征，研究β-环糊精的作用机理及其对催化剂加氢性能的影响。研究结果表明：在反应温度为260 ℃、反应压力为7 MPa、反应时间为2.0 h的最优条件下，采用Ni/SFCC-CD催化C9石油树脂加氢，可制得溴值为1.45 gBr/（100 g）、色号（加纳德）小于1的水白色氢化C9石油树脂，催化剂循环使用4次后仍保持良好活性；β-环糊精的作用机理是：β-环糊精与硝酸镍产生络合作用，抑制硝酸镍的分解、控制NiO的结晶过程和增强活性组分Ni与载体之间的相互作用力，从而提高了Ni/SFCC-CD的催化活性和稳定性。     

Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

孤岛工作面撤出支架时的顶板加固及撤出工艺

11210高水充填工作面作为孤岛工作面,末采阶段顶板压力大。采用锚网支护控制工作面顶板,撤架时利用掩护架保证撤架空间安全,利用移架平台撤出剩余支架,实现了安全生产。     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。     

S6-11综放工作面回风巷支护设计优化

针对常村矿回采巷道变形严重,影响正常生产的问题,通过对矿井赋存条件、巷道现有支护形式和围岩变形过程分析,采用新型联合支护技术对S6-11回风巷道支护进行优化。现场实测巷道顶底板相对移近量最大120mm,两帮相对移近量最大140mm,均在允许正常范围之内。     

掘进巷道快速过断层施工技术应用

基于四候煤矿3108回风顺槽过F3断层期间,顶板出现严重破碎、下沉现象,提出了俯斜台阶法施工工艺,并对断层破碎带顶板采取MF-2型化学材料注浆加固以及"钢筋锚索网+U29梯形棚"联合支护措施。支护效果检验结果表明,联合支护有效控制了断层破碎区顶板下沉、破碎现象,保证了巷道顶板稳定性。     

半纤维素基阿维菌素载药微囊的制备及性能

目前阿维菌素以高效性、无污染和低抗药性等特点而得到广泛应用，但是其稳定性较差，易降解导致使用量较大从而造成浪费。为解决上述问题，本文以半纤维素为基体，利用原位聚合法制备阿维菌素载药微囊（HDCM），通过制备条件、热降解性、储存稳定性和释放动力学研究，确定了HDCM的载药量、热稳定性及释放性能。结果表明，在芯壁比为1∶34（质量比），温度为65℃，pH为3.5的制备条件下，HDCM的载药量可达66.5%，粒径较小且分散均匀。HDCM的热降解性能和恒温热稳定性能较阿维菌素原药有所提高，最高热分解温度从261℃增加到272℃，阿维菌素原药10h后降解率达到12.1%，而载药量为66.5%的HDCM降解率仅为5.2%。HDCM的释放机理满足Fick扩散，阿维菌素原药在水中的累积释放率在12h之内达到83.8%，而HDCM的累积释放率在24h之后才有所增大，12h内其释放率仅为33.7%，表明HDCM具有极好的缓释性能。     

Kinetic,thermodynamic parameters and in vitro digestion of tannase from Aspergillus tamarii URM 7115

Tannase is an enzyme used in various industries and produced by a large number of microorganisms. The aim of this study was to evaluate tannase production to determine the biochemical, kinetic, and thermodynamic properties and to simulate tannase in vitro digestion. The tannase-producing fungal strain was isolated from “jamun” leaves and identified as Aspergillus tamarii. Temperature at 26°C for 67?h was the best combination for maximum tannase activity (6.35-fold; initial activity in Plackett–Burman design—15.53?U/mL and average final activity in Doehlert design—98.68?U/mL). The crude extract of tannase was optimally active at 40°C, pH 5.5 and 6.5. Moreover, tannase was stimulated by Na⁺, Ca²⁺, Mg²⁺, and Mn²⁺. The half-life at 40°C lasted 247.55?min. The free energy of Gibbs, enthalpy, and entropy, at 40°C, was 81.47, 16.85, and ?0.21?kJ/mol?·?K, respectively. After total digestion, 123.95% of the original activity was retained. Results suggested that tannase from A. tamarii URM 7115 is an enzyme of interest for industrial applications, such as gallic acid production, additive for feed industry, and for beverage manufacturing, due to its catalytic and thermodynamic properties.